Dell equallogic group manager download3/12/2024 ![]() The blade servers, although following the traditional naming strategy e.g. M520, M620 (only blades supported) are not interchangeable between the VRTX and the M1000e. The blades differ in firmware and mezzanine connectors. In 2018 Dell introduced the Dell PE MX7000, a new MX enclosure model, next generation of Dell enclosures. The M1000e enclosure has a front-side and a back-side and thus all communication between the inserted blades and modules goes via the midplane, which has the same function as a backplane but has connectors at both sides where the front side is dedicated for server-blades and the back for I/O modules. Indication on back of chassis to see which midplane was installed in factory The server-blades are inserted in the front side of the enclosure while all other components can be reached via the back. The original midplane 1.0 capabilities are Fabric A - Ethernet 1Gb Fabrics B&C - Ethernet 1Gb, 10Gb, 40Gb - Fibre Channel 4Gb, 8Gb - IfiniBand DDR, QDR, FDR10. The enhanced midplane 1.1 capabilities are Fabric A - Ethernet 1Gb, 10Gb Fabrics B&C - Ethernet 1Gb, 10Gb, 40Gb - Fibre Channel 4Gb, 8Gb, 16Gb - IfiniBand DDR, QDR, FDR10, FDR. The original M1000e enclosures came with midplane version 1.0 but that midplane did not support the 10GBASE-KR standard on fabric A ( 10GBASE-KR standard is supported on fabrics B&C). To have 10Gb Ethernet on fabric A or 16Gb Fibre Channel or InfiniBand FDR (and faster) on fabrics B&C, midplane 1.1 is required.Ĭurrent versions of the enclosure come with midplane 1.1 and it is possible to upgrade the midplane. Via the markings on the back-side of the enclosure, just above the I/O modules: if an "arrow down" can be seen above the 6 I/O slots the 1.0 midplane was installed in the factory if there are 3 or 4 horizontal bars, midplane 1.1 was installed.Īs it is possible to upgrade the midplane the outside markings are not decisive: via the CMC management interface actual installed version of the midplane is visible Front:Blade servers Įach M1000e enclosure can hold up to 32 quarter-height, 16 half-height blades or 8 full-height or combinations (e.g. #DELL EQUALLOGIC GROUP MANAGER GUI DOWNLOAD UPGRADE# When using full-height blades one use slot n (where n=1 to 8) and slot n+8 The slots are numbered 1-16 where 1-8 are the upper blades and 9-16 are directly beneath 1-8. Integrated at the bottom of the front-side is a connection-option for 2 x USB, meant for a mouse and keyboard, as well as a standard VGA monitor connection (15 pin). Next to this is a power-button with power-indication. Next to this is a small LCD screen with navigation buttons which allows one to get system-information without the need to access the CMC/management system of the enclosure. Basic status and configuration information is available via this display. To operate the display one can pull it towards one and tilt it for optimal view and access to the navigation button. For quick status checks, an indicator light sits alongside the LCD display and is always visible, with a blue LED indicating normal operation and an orange LED indicating a problem of some kind. This LCD display can also be used for the initial configuration wizard in a newly delivered (unconfigured) system, allowing the operator to configure the CMC IP address. ![]() Back:power, management and I/O Īll other parts and modules are placed at the rear of the M1000e. A standard M1000e operates with three PSU's The rear-side is divided in 3 sections: top: here one insert the 3 management-modules: one or two CMC modules and an optional i KVM module.Īt the bottom of the enclosure there are 6 bays for power-supply units. ![]() The area in between offers 3 x 3 bays for cooling-fans (left - middle - right) and up to 6 I/O modules: three modules to the left of the middle fans and three to the right.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |